Sony SupportDSC-RX100M5

DSC-RX100M5 Camera Firmware Update (Mac)

    Required Downloads
    Applicable Models
    About this download
    System Requirements
    File Info
    Preparation
    Download & Install
    WAIT - Read the Required Files section before downloading this file.

    Required Downloads

    Unless stated otherwise, the file listed below must be installed BEFORE the DSC-RX100M5 Camera Firmware Update (Mac) in order for it to work properly. If more than one Required file is listed, install them in the order presented on this page.

    IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

    This information is for the following models:

    • DSC-RX100M5

    About this download

    Benefits and improvements

    This utility updates the camera firmware to version 2.00 and provides the following benefits:

    Improvements over version 1.01:

    • Improves operability with the MPK-URX100A Underwater Housing:
      • Adds the Underwater Auto feature in the White Balance settings
      • Adds the Flash Off mode when the Flash unit is popped-up
    • Improves the overall stability of the camera

    Benefits provided by previous updates and included in version 2.00:

    • Improves a condition where the camera will not power-on after making certain setting changes
    • Improves overall stability of the camera

    System Requirements

    Operating Systems

    • Mac OS® X

    File Info

    File Name

    • Update_DSCRX100M5V200.dmg

    File Version

    • 2.00

    File Size

    • 265.25 MB

    Release Date

    • 03-29-2017

    Before You Start

    Determine if Your Camera Needs the Update

    This update only applies to DSC-RX100M5 cameras that currently have a firmware version 1.01. If your camera firmware version is already version 2.00, this update is not necessary.

    Check the version of your camera firmware:

    1. Power on the camera.
    2. Press the Menu button.
    3. At the Menu screen, use the Control Wheel to select Setup, and then select Version.
      Menu Version Screen
    4. The firmware version is displayed on the LCD screen.
      Firmware Version Screen
    5. If the current firmware version is 2.00, the camera does not need this update.
    6. Press the center button of the Control Wheel to close the version number display.

    Important Notes

    • WARNING! This utility is only for use with the Sony® DSC-RX100M5 camera. Do not install this utility with any other model.
    • WARNING! This Digital Camera firmware update and any changes incurred by it are permanent. It is not possible to return to a previous firmware version after updating this firmware. By continuing this update process and downloading and updating this firmware, you acknowledge that you are aware and understand that this update cannot be reversed.
    • WARNING! Do not choose About This System Software Updater from SystemSoftwareUpdater Menu. Doing so may cause the updater software to crash, especially while updating.
    • WARNING! Do not allow the computer to enter Sleep (Standby) mode during the update process. To change your settings, please refer to your computer manual or consult the manufacturer.
    • This update process requires the following items for proper updating:
      • A computer with:
        • CPU: Intel® processor (Core Solo™ and Core Duo processors are no longer supported)
        • Available Hard Disk Space: 600 MB or more
        • Installed Memory (RAM): 512 MB or more
        • A USB port.
        • Apple® Mac® OS X® version 10.9 - 10.13
          IMPORTANT: For computers running Mac OS X version 10.13 – 10.15, the DriverLoader_1015 software must be installed before installing the camera software update for each camera that's being updated.

          IMPORTANT: For computers running macOS 11 – 12, the System Software Update Helper software must be installed before installing the camera software update for each camera that's being updated.

      • Camera power supply:
        • This update can only be performed when the remaining battery level has three bars Battery Indicater or more. When performing the firmware update, use a fully charged NP-BX1 rechargeable battery pack, or the AC adapter/charger.
          WARNING! The camera may not operate properly if the power is interrupted during the update.
      • USB cable:
        • Use only the USB cable supplied with the camera.
          IMPORTANT: Update functionality is not guaranteed with any other USB cable.
    • To ensure that no other program interferes with the installation, save all work and close all other programs.
    • It is highly recommended that you print out these instructions for use as a reference during the installation process.

    Prepare the Camera for the Firmware Update

    1. Remove the memory card from the camera
    2. Ensure the camera has a fully charged battery pack or connected to the AC adapter/charger.

    Download & Install

    Download and Update the Firmware

    1. WARNING! Do not choose About This System Software Updater from SystemSoftwareUpdater Menu. Doing so may cause the updater software to crash, especially while updating.

      WARNING! Do not allow the computer to enter Sleep (Standby) mode during the update process. To change your settings, please refer to your computer manual or consult the manufacturer.

    2. Download the Update_DSCRX100M5V200.dmg file to a temporary or download directory (please note this directory for reference).
    3. Go to the directory where the file was downloaded and double-click the Update_DSCRX100M5V200.dmg file.
      Note: Do not connect the camera to the computer yet.
    4. On the desktop, double-click the SystemSoftwareUpdater System Software Updater Icon icon.
    5. At the prompt, enter the Username and Password for the administrative account, and then click OK.
      System Software Updater Password
    6. The System Software Updater starts.
      Connect the Camera Screen
    7. Press the Menu button on the camera.
    8. At the Menu screen, use the Control Wheel to select Setup, USB Connection, and then ensure that Mass Storage is selected.
      Mass Storage USB Setting
    9. Connect the camera to the computer with the supplied USB cable.
      Note: On the camera screen USB Mode is displayed.
      • If the computer displays the message, Could not find the camera for this update:
        1. Disconnect the USB cable and connect it again.
        2. If the computer has multiple USB ports, connect to a different port.
      • If a message appears on the computer recommending a restart:
        1. Disconnect the camera from the computer.
        2. Remove the battery and/or AC adapter from the camera, and then reconnect them.
        3. Restart the computer and then retry the update from starting the Software Updater (step 2 above).
    10. When the updater recognizes the camera connection, the following screen is displayed.
      Camera Connected Screen
    11. Confirm that Current version is 1.01, and that the Version after the update is 2.00, and then click Next.
      Note: If the Current version is 2.00, this update is not needed. Stop the USB connection, and click Finish, then remove the battery pack and/or AC adapter and restart the camera.
    12. The following screen appears and the camera automatically resets.
      Camera Reset Screen
    13. After the camera resets, the following screen appears and the update starts.
      Note: The progress bar is displayed during the update which takes about 15 minutes.
      Run the Update Screen

    14. WARNING! Do not power off the camera or disconnect the USB cable during the update.

    15. When the update is complete, the camera will automatically restart and the following screen is displayed.
      Update Complete Screen
    16. Wait until the camera finishes restarting, click Finish, and then disconnect the USB cable.
      Note: After restarting, the message Recovering data Please wait... may rarely display. This is normal, please wait until this message goes away.
      Recovering data Please wait... message

    Check the Firmware Version After Updating (optional)

    1. Power on the camera.
    2. Press the Menu button.
    3. At the Menu screen, use the Control Wheel to select Setup, and then select Version.
      Menu Version Screen
    4. The firmware version is displayed on the LCD screen.
      Firmware Version Screen
    5. If the current firmware version is 2.00, the firmware update was successful.
      Note: If the firmware version number is not 2.00, please download and install the firmware update again.
    6. Press the center button of the Control Wheel to close the version number display.