ILCE-6400 System Software (Firmware) Update Ver. 2.00 (Mac)

Important notice

• Use a fully charged rechargeable battery pack NP-FW50 or the AC adaptor AC-PW20 (sold separately).
• Do not remove the battery during the update; as the sudden loss of power may render the camera inoperable.
• Remove the memory card from the camera before starting the update process.
• Prevent your computer from entering Sleep mode.
• Do not open "About This System Software Updater" in the System Software Updater menu as this may cause the Updater software to crash.
• Do not connect the camera to other any other devices except your computer.
• Do not connect the camera to the computer before the instruction.

How to download the Updater:

1. After reading the disclaimer, click Download.
2. The [Update_ILCE6400V200.dmg] file will start downloading.
3. Save the file to the desktop of your computer (recommended).

Step 1: Start the Updater

1. Close all currently programs currently running on your computer.
2. Double-click the [Update_ILCE6400V200.dmg] file you downloaded. Do not connect the camera at this point.
   NOTE: If you have connected the camera to a computer, remove it before following the procedure.
3. [Update_ILCE6400V200] is expanded.
4. Double-click the [UpdateSetting Tool] icon.
   
5. To load a kernel extension, the message prompts you to allow the application to make changes. Type the password for the administrative account.
   
   
   • For macOS 11 – 12 users
     

     If your computer is running on macOS 11 – 12, you also need to download the System Software Update Helper. Go to the download page below,
     follow the instructions, and download the System Software Update Helper to start the updater.
     If your computer is running on another OS, follow the procedure below.

   • For macOS 10.15 users
     

     If your computer is running on macOS 10.15, you also need to download the Driver Loader. Go to the download page below,
     follow the instructions, and download the Driver Loader to start the updater.
     If your computer is running on another OS, follow the procedure below.

   • For macOS 10.13 or 10.14 user, once the message from the system displays, the security and privacy screen will be displayed.
     • If the following message is displayed before "Security and Privacy" is displayed, press the [OK] button.
       
     • Open the "General" tab on the "Security and Privacy" screen and allow reading of the "Sony Corporation" system software.
       NOTE: If you have approved this in the past, the security and privacy screen will not be displayed. If you are asked to restart macOS after clicking the [Allow] button, please restart and return to the beginning of the update procedure.
       
     • If the "Security and Privacy" screens does not disappear, please close the window.
     • If both the message displayed and the "Security and Privacy" screen do not disappear, close both using the [OK] button.
       
6. Connect the camera to the computer
   • A dialogue box for the USB connection will be displayed.
     
   • Connect the camera to the PC using the USB cable (supplied). "USB Mode" appears on the LCD monitor of the camera.
     NOTE: If the USB cable was connected before the dialog prompting for USB connection appears, disconnect the USB cable and start the updater again.
   • Click [OK]. If the message is displayed, close using the [OK] button.
     
     NOTE: Never turn off the camera nor disconnect the USB cable while updating.
7. The System Software Updater will start.
   
   NOTE: If the System Software Updater does not start up, double-click [System Software Updater] in the [Update_ILCE6400V200] - [Resources] folder to start up.
8. Turn on the camera.
9. Follow the instructions in the System Software Updater window, on the camera, select "Menu" > "Setup subpage [4]" > "USB Connection" and check if "Mass Storage" has been selected.
   NOTE: If a mode other than Mass Storage is selected, please select Mass Storage.
   
10. Click [Next]. The current version number and updated version number appear on the lower left-hand side of the screen. After confirming that the current software version is "Ver. 1.00 or earlier", click [Next]. If the current system software version is 2.00 or later, the update is not required. In this case, disconnect the camera from the computer and click [Finish]. Turn off the camera, remove the battery pack, reinsert the battery and turn the camera back on.
    • Update is required:
      
    • Update is not required:
      
11. The camera will automatically be reset.
    
    NOTE: The Loading icon may not be displayed depending on the OS version that you are using.
12. Start the update
    NOTE: After automatically resetting, the following screen is shown and the update starts. The progress bar appears during the update process (approximately 15 minutes). Never turn off the camera or disconnect the USB cable while updating.
    
13. Once the update has been completed, the camera will automatically restart. Make sure that the camera is turned on and wait until the LCD screen appears again. Click [Finish] when the LCD screen appears and disconnect the USB cable.
    
    NOTE: After restarting, a data recovery warning is sometimes displayed. This is normal. Please wait until this warning disappears.
    

Step 2: Confirm that the system software version of your device is Ver. 2.00.

1. On the camera, select "Menu" > "Setup subpage [7]" > "Version".
2. The system software version is displayed as illustrated.