HVL-F60RM System Software (Firmware) Update Ver.2.01 (Mac)

Important notice

• Use four new LR6 (AA size) alkaline batteries or four fully charged AA-sized rechargeable nickel-metal hydride (Ni-MH) batteries.
• Do not remove the battery during the update; otherwise, the device may become inoperable due to the sudden power shutdown.
• Prevent your computer from entering Sleep mode.
• Ensure all devices except the computer are disconnected.

Install the driver:

Please do these operations while connected to the Internet.

When updating this device, the device driver provided by Silicon Labs is required.

Download the following file. Save the downloaded file on your computer desktop (recommended).

• SiLabsUSBDriverDisk.dmg

1. Double-click the downloaded file "SiLabsUSBDriverDisk.dmg". Do not connect the device at this time.
2. [Sillicon Labs VCP Driver Install Disk] folder is displayed.
3. Double-click the [Install CP210x VCP Driver] in the folder.
4. The installer screen is displayed. Click [Continue] to proceed.
   
5. The software license agreement screen is displayed. Click [Agree].
   
6. Permission to install the helper tools will be required. Enter the password when you logged in with an administrator account.
   
7. Once the extension is blocked, open the "Security & Privacy" system preferences
   
8. Click the key in the "Security & Privacy" system preferences and select [Allow].
   

How to download the Updater:

1. Make sure that you are logged on as a user with administrative rights.
2. After reading the disclaimer, click Download.
3. The file [Update_HVLF60RMV201.dmg] file will start downloading.
4. Save the file to the desktop of your computer (recommended).

Step 1: Start the Updater

1. Close all currently programs currently running on your computer.
2. Double-click the [Update_HVLF60RMV201.dmg] file you downloaded. Do not connect the device at this point.
3. [Update_HVLF60RMV201] is expanded.
4. Double-click the icon.
5. To load a kernel extension, the message prompts you to allow the application to make changes. Type the password for the administrative account.
   


6. System Software Updater starts up.
   


7. Turn on the device.
8. Use USB-standard cable or USB cable attached to the camera. Then connect the computer and the device. The LCD monitor of the device turns off when it is connected with the USB cable.
   
   NOTE: If the computer cannot find the device, the message "Could not find the device for this update." appears on the computer display. Try the following if this happens.
   • Disconnect the USB cable and connect it again.
   • If the computer has multiple USB terminals, try with the other terminals.


9. After confirming the LCD monitor for the device, click [Next]. The current version and the version after the update appear on the lower left part of the screen.
   After confirming [Current version] is "Ver.2.00" or earlier, click [Next].
   
   NOTE: If the current system software version is "2.01" or later, the update is not required.
   In this case stop the USB connection and click [Finish], turn off the device, remove the battery pack, reinsert the battery and turn the device back on.
   
   Update is required
   
   
   Update is not required
   


10. The device automatically resets.
    The below screen below appears.
    
    NOTE: Loading icon may not be displayed depending on the OS version you are using.


11. Start the update
    After automatically resetting, the following screen appears and the update starts. The progress bar appears while updating (approximately 10 minutes).
    NOTE: Never turn off the device nor disconnect the USB cable while updating.
    


12. Complete the update
    Once the update is complete, the screen below will be shown. The device will automatically reboot, which may take a few minutes.
    When the screen appears, press the [Finish] button and disconnect the USB cable. Turn off the device and turn it on again.
    
    

Step 2: Confirm the system software version of your device is Ver.2.01.

1. Select [Menu] → [2/2] → [VERSION] → [FLASH] on the device.
2. The system software version is displayed as illustrated below.