LA-EA3 Firmware Update (Windows)

IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

This information is for the following models:

ILCE-9
LA-EA3

About this download

Benefits and improvements

This update enables the camera to focus continuously on a subject during continuous shooting at speeds up to 10 fps (using Hi or Mid Continuous Shooting mode) when the adaptor is attached to the ILCE-9 camera.

Notes: This Lens system software update is available for the E-mount body.

Some models cannot be used for this update. (model list)
When using PXW-FS7M2, please follow the procedure according to the instruction manual of PXW-FS7M2.

System Requirements

Operating Systems

Windows® 10
Windows® 10 64-bit
Windows® 7
Windows® 7 64-bit
Windows® 8.1
Windows® 8.1 64-bit

File Info

File Name

Update_LAEA3V200.exe

File Version

File Size

8.89 MB

Release Date

05-24-2017

Before You Start

Determine if you need this update

Check the version of your lens adaptor System Software:

Attach the lens adaptor to the camera.
Note: Please make sure the camera is off before you attach the lens adaptor.
Power on the camera.
Press the Menu button.
At the Menu screen, select Setup.
At the Setup screen, select Version.
The System Software version is displayed on the LCD screen.

Note: If the current System Software version is Ver.02 or higher, the camera lens adaptor doesn't need this update.

Before You Start

This System Software update can be performed only when the lens adaptor is attached to a camera. Don't install this update with any other model.
WARNING! This System Software update and any changes incurred by it are permanent. It's not possible to return to a previous version after updating this System Software. By continuing this update process and downloading and updating this System Software, you acknowledge that you are aware and understand that this update can't be reversed.
This update process requires the following items for proper updating:
- A computer with:
  - Available Hard Disk Space: 200 MB or more
  - Installed Memory (RAM): 512 MB or more
  - A USB port.
  - One of the following operating systems installed:
    - Microsoft® Windows® 10
    - Microsoft® Windows® 8.1
    - Microsoft® Windows® 7 (with Service Pack 1)
- This Lens system software update is available for the E-mount body.
  - Some models cannot be used for this update. (model list)
  Note: Camera models NEX-5R and NEX-6 require firmware version 1.01 or higher, for the latest camera firmware information, please visit the NEX-5R or NEX-6 support page.
- A USB cable: Use only the USB cable supplied with the camera.
  Note: Update functionality isn't guaranteed with any other USB cable.
When performing the update, please use a fully charged battery pack, or the AC adaptor/charger (sold separately).
Note: When performing the update using a Broadcast & Production camera, please use the dedicated AC adaptor.
Detach the vertical grip before updating lens adaptor system software.
WARNING! Don't remove the battery pack or AC adapter during the update process, otherwise, the camera may become inoperable due to the sudden power loss.
To keep other programs from interfering with the installation, save all work and close all other programs before proceeding.

Download & Install

Installation Instructions

Download the Update_LAEA3V200.exe file to a directory on your computer, and make note of this directory for reference.
Go to the directory where the file was downloaded and double-click the Update_LAEA3V200.exe file.
Remove the memory card from the camera.
Make sure the lens adaptor is attached the camera.
Note: Please make sure the camera is off before you attach the lens adaptor.
Power on the camera.
Note: If the camera has already been powered on, power it off and then back on again.
On the camera, press the Menu button, select Setup, and then USB Connection and make sure Mass Storage is selected (this step isn't necessary if you are using a QX series camera).
Connect the camera to your computer using the supplied USB cable.
Note: If an error message appears on the computer screen, try the following:
- Disconnect the USB cable and then reconnect it.
- If another USB port is available on the computer, try connecting the USB cable to another port.
Verify that the remove hardware icon or is displayed in the task tray at the lower right-hand corner of the computer screen.
After confirming the steps above, at the Lens System Software Updater screen, click Next.
The camera screen displays the message Follow computer instructions.
Notes:
- If the message The update isn't available for your model. appears on the screen, verify that the update file is correct for the lens adaptor you have attached. If the file is correct, close the Lens System Software Updater program, disconnect the USB cable, power off the camera, and then restart the Lens System Software Updater program and continue the procedure.
- If the message Could not find the camera with the lens adaptor for this update mounted. appears on the screen, make sure you are using a compatible camera and if the camera is properly connected to the computer. Try disconnecting and reconnecting the USB cable or connect to another USB port on the computer.
  Notes: This Lens system software update is available for the E-mount body.
  - Some models cannot be used for this update. (model list)
At the Lens System Software Updater screen, check the version number at the lower left.

Note: If the current version is Ver.02, your lens adaptor doesn't need this update. Stop the USB connection by clicking the remove hardware icon or in the task tray in the lower right corner of the computer screen. Then disconnect USB cable from the camera and click the Finish button on the Lens System Software Updater screen. Power off the camera, briefly remove the battery pack or the AC adaptor, and then power on the camera again.

If the current version is Ver.01, click Next to continue with the update.
The following screen is displayed and the progress bar appears while transferring data to the camera (data transfer takes approximately 5 seconds).

WARNING! Do not power off the camera or disconnect the USB cable until the update process is complete.
When the data transfer is complete, the following screen is displayed, click Finish.
The update process starts and the progress bar is displayed on the camera screen. This process takes approximately 30 seconds to complete.
The update process is finished when the Lens adaptor update complete. message is displayed on the camera screen.
Note: If you are using the QX series, the update process is finished when the message disappears from the camera screen.
Stop the USB connection by clicking the remove hardware icon or in the task tray in the lower right corner of the computer screen. If the icons aren't present in the task tray, please proceed to the next step.
Disconnect the USB cable, power off the camera, and then remove the battery pack or AC adaptor.
Reconnect the battery pack or AC adaptor and power on the camera.
Check the current firmware version to confirm that the update has successfully installed.
- If the version is Ver.02, the firmware update was successful.
- If the version isn't Ver.02, download and install the update again.

Product Repair
Repair information and service assistance
Community
Here you can ask questions and connect with other Sony users
Parts & Accessories
Product information and sales assistance
Register a Product
Keep track of all your products in one location
Contact Support
Product support & customer relations
Support by Sony (Mobile App)
Get Support Content on the Go!